|
|
 |
ACE BACKSTAGE CO., INC. - STAGE POCKET SYSTEMS |
661-295-5760 |
 |
SPECIALIZING IN STAGE POCKET SYSTEMS SINCE 1991 |
 |
 |
 |
 |
STANDARD VERTICAL SLANT PANEL STAGE POCKETS |
 |
ABOUT ACE BACKSTAGE CO., INC. |
|
 |
 |
 |
 |
 |
 |
| UL Listed |
Standard |
Connectrix |
Data |
Specs |
Specs |
 |
DESCRIPTION |
 |
|
Ace Backstage Co. Inc.'s extra large-sized Stage Pocket, the Double Wide Stage Pocket, is a standard general use vertical slant panel flush stage pocket. The Double Wide Stage Pocket is made of heavy duty steel and may be used to conceal audio, communications, control, data, electric AC power, switches, video, and voice connections etc. below the floor surface for easy access and to prevent connector damage. The Double Wide Stage Pocket has an extra large capacity inter-changeable panel system which permits easy custom connector/panel configurations.
The Double Wide Stage Pocket has the panel capacity for either:
• (4) #PNL-100 Series "Connectrix" Panels or
• (2) #PNL-120 Series "Connectrix" Panels or
• (4) #PSW-100 Series Switchcraft® Panels or
• (4) #PE Series Single Gang Electric Duplex Switch Box Panels or
• (2) #FP3E Series Triple Gang Electric Duplex Switch Box Panels
The Double Wide Stage Pocket has the connector capacity for either:
• (24) "Connectrix" Connectors or
• (24) Neutrik® Connectors or
• (24) Switchcraft® Connectors or
• (12) "Connectrix", Neutrik®, or Switchcraft® Connectors and (2) #PE Electric Duplex Switch Box Panels
Utilizing ACE's "Connectrix" System will allow mounting of up to 24 "Connectrix", Neutrik®, Switchcraft®, and/or Custom Connectors in the Double Wide Stage Pocket. All ACE Double Wide Stage Pockets are welded steel construction, with a 1/8" (nominally 10 ga. (.135")) thick CRS steel Lid, a 1/8" (nominally 11 ga. (.120")) thick CRS steel Mounting Flange, and a 16 ga. (.062") thick Pocket Body. The Double Wide Stage Pocket resists bending under even the most severe stage loads.
Removable spring loaded hinge pins permits easy exchange of lids for carpet lids, locking lids, standard lids, and other custom application lids. A generous cable way slot of 3/8" x 16" permits easy cable exit from the stage pocket, even for large gauge cables. Two cableway slot channel closures closes the slot when not in use. The Double Wide Stage Pocket has an easy installation into 16.8" x 8.5" cutout in the stage floor. Open easy access from top or back of the Double Wide Stage Pocket to connector panels makes for easy installation.
A scratch/wear resistant finish, oven cured powder coat is electro-staticly applied inside and outside the entire Stage Pocket. Decorator neutral Antique Copper Vein or Textured Black finishes are standard. A Solid Brass Lid and Mounting Flange as well as Solid Stainless Steel Lid and Mounting Flange are also available by special order. TheDouble Wide Stage Pocket's solid rubber Lid Stops cradle the lid to prevent lid rattle.
ACE's Standard Vertical Slant Panel Stage Pocket Systems offer "Connectivity" Solutions with a flexible, reliable, and simplistic design. The flexible design of the Standard Vertical Slant Panel Stage Pocket Lid, Mounting Flange and Pocket Body along with Custom and Prefabricated Aluminum "Connectrix" (Neutrik®/Switchcraft® combo cutout) Panels, Switchcraft® Panels, and our large selection of "Connectrix" (Neutrik®/Switchcraft® combo cutout), Switchcraft®, and Custom Connectors allow the Stage Pockets to be installed in many different applications. These applications include educational, institutional, and liturgical settings. Within these applications various audio, communications, control, data, electric AC power, video, and voice terminations are possible, allowing for a complete Stage Pocket System.
ACE's Standard Vertical Slant Panel Stage Pockets are available in a variety of sizes (Mini, Half, Full, and Double Wide) making them flexible in both form and function and able to meet your individual requirements. All Standard Vertical Slant Panel Stage Pockets are UL Listed except for the Mini Pocket. For more details on Ace Backstage Co. Inc.'s Stage Pocket Systems call the Ace Order Desk at 661-295-5760.
|
|
|
|
|
|
SPECIFICATIONS |
|
|
• Double Wide Stage Pocket Data Specification Sheet (AutoCAD® dwg format)
• Double Wide Stage Pocket Data Specification Sheet (AutoCAD® dxf format)
• Double Wide Stage Pocket Data Sheet (Adobe® pdf format)
• Double Wide Stage Pocket Body Size = 16.000” W x 4.500” H x 7.187” D
• Double Wide Stage Pocket Lid & Mounting Flange Size = 18.500” W x 0.937” H x 10.500” D
• Double Wide Stage Pocket Connector Capacity = Up to 24 “Connectrix”, Neutrik®, or Switchcraft®
• Double Wide Stage Pocket Cutout Dimensions = 16.800" W x 8.500" H
• Double Wide Stage Pocket Material = CRS Steel and/or Solid Half Hard Brass
• Double Wide Stage Pocket Panel Capacity =
• (4) #PNL-100 Series “CONNECTRIX” Panels OR
• (4) #PSW-100 Series Switchcraft® Panels OR
• (4) #PE Series Single Gang Electric Duplex Switch Box Panels OR
• (2) #FP3E Series Triple Gang Electric Duplex Switch Box Panels OR
• (2) #PNL-120 Series “Connectrix” Panels
|
|
|
|
|
|
CONNECTORS |
|
|
|
 |
 |
| Connectrix |
Custom Cut |
Switchcraft® |
"CONNECTRIX" Connectors = Neutrik® "D" and Switchcraft® "E" Connector Mounts
Custom Cut Panel Connectors = Custom Cut Connector Mounts
Switchcraft® Connectors = Switchcraft® "D" Connector Mounts
“CONNECTRIX” CONNECTORS COMBINE NEUTRIK® “D” AND SWITCHCRAFT® “E” MOUNTING HOLE PATTERNS FOR GREATER FLEXIBILITY
The “Connectrix” system connectors may be used in any of the “Connectrix” panels utilizing the popular mounting pattern of the Neutrik “D” and Switchcraft “E” series mounting patterns. Connectors using the generous rectangular “Connectrix” cutout will add to a growing array of adapter-mounted standard connectors. The adapter mount is plastic and provides ground isolation between the panel and connector. Click on the links above for our current selection of stock “Connectrix” system connectors.
When ordering, please specify model number and type of connector as well as panel model number (#PNL-100 Series, #PNL-120 Series, or #PSW-100 Series) the connectors will be loaded into. *NOTE: Specific High Density (HD) and Sub-D pattern connectors will require either 2 or 3 “Connectrix” Horizontal Spaces or 2 or 3 “Connectrix” Vertical Spaces, depending on connectors selected. Connectors may be loaded into panels with nutcerts and nut/bolts or black aluminum pop rivets.
|
|
|
|
|
|
PANELS |
|
|
|
|
|
| Connectrix |
Custom Cut |
Switchcraft® |
"CONNECTRIX" Panels = "Connectrix" Panels combine Neutrik® "D" and Switchcraft® "E" Connector Mounts
Custom Cut Panels = Custom Cut Panels with Custom Connector Mounts
Switchcraft® Panels = Utilize Switchcraft® "D" Connector Mounts
“CONNECTRIX” SYSTEM PANEL DESCRIPTION
Many pre-cut stock #PNL-100 Series, #PNL-120 Series “Connectrix” System connector panels and #PSW-100 Series Switchcraft® connector panels are available for the Double Wide Stage Pocket. Standard "Connectrix" and Switchcraft® Panels are created from high strength, tough, aircraft aluminum alloy (6061-T6) that is 1/16" (.062") or 1/8" (.125") thick. The standard panels mount with (4 or 6) self-tapping screws. Each panel is CNC machined to precisely mate with the designated connectors and in the pocket mounting holes. Each Standard "Connectrix" and Switchcraft® Panel is finished with oven cured semi-gloss black powder coat.
Most panels provide header space for custom engraving which is fast and easily accomplished on a separate dedicated CNC engraving machine. The finished panels show bright aluminum in the engraved characters and need not be back filled. ACE standard panels are flat, strong, and rigid like the typical thinner mild steel panels. Because the panels are machined and not punched they stay flat and undistorted unlike punched panels which distort in the punching process. The machined “Connectrix” style cutouts combine popular mounting patterns of the Neutrik “D” series and Switchcraft “E” series connectors with a generous rectangular cutout that mates with a growing array of adapter-mounted standard connectors. The adapter mount is plastic and provides ground isolation between the panel and connector.
Using the “Connectrix” system panel it is possible to mount any combination of modular jacks (RJ45, RJ11 etc.), BNCs, dual RCAs, mic jacks, speaker jacks and numerous other standard connectors without a single custom punch. This system provides for more connectors and mounting options in stock standard ACE panels. The benefit is faster order turn around and lower cost. Less custom fabrication for custom spec results with off-the-shelf stock prices.
|
|
|
|
|
|
PANEL CAPACITY - #124xxxx DOUBLE WIDE POCKET |
|
| |
